How To Make A Harness For Your Fat Cat With Pictures

For the sake of our example, let’s assume our three measurements are 8”, 6” and 15”, where 8” and 15” are the two circle circumferences.

The paper you use will have to be at least as wide as your cat’s larger circle measurement plus a couple of inches, and as tall as your cat’s length measurement plus a couple of inches. In our example, you’ll need a piece of paper at least 17” wide and 8” tall to be certain the pattern will fit on it. Alternatively, you can use two separate pieces of paper taped together. Since you don’t need any special paper to draw a pattern, you could use a piece of a newspaper, the back of a poster, or something similar. The exact shape and design of the cat jacket can be anything you want, but the important parts to remember is that each section you measured on your cat has to be the same size on the pattern. However, since you’ll need to add velcro to the two circles that go around your cat, you’ll need to make sure these flaps overlap each other so both sides of the velcro will touch.

Once the pattern is complete, cut it out and test it on your cat. If any sections don’t fit, draw a new pattern and try again.

If you prefer, you can use regular fabric as the lining, in which case you’ll need enough fabric to cut out 2 full sections using the pattern. You can use any type of fabric you want, but you may find lightweight cotton to be the easiest to sew. And it comes in the largest selection of patterns and colours. An alternative to cotton for the outside of the jacket could be polar fleece - which comes in a multitude of colours as well. In this case you might consider a satin-like material for the lining. Interface fabric is normally used to strengthen or thicken another type of fabric. As such it is not a requirement for the jacket unless you feel you need to reinforce the fabric you’re using. If you want to use interfacing, make sure it is the same weight, or less, than the fabric you’re using. If you decide to use cotton, you’ll want to look for standard non-woven interfacing. If you’re using polar fleece, which is stretchy, you’ll want to look for knit interfacing. The nylon webbing needs to be at least as long as the middle, straight-line measurement you took of your cat. Ideally you should pick a colour that matches your fabric. The thickness of the webbing is really up to you, based on the look you want, what might match your fabric, and how heavy your cat is. The thicker the webbing, the harder it will be to sew to the jacket using your sewing machine’s “normal” needle. The D ring needs to be at least wide enough to allow the nylon webbing to be placed through it. For example, if you buy a D ring that’s ½” wide, your nylon webbing has to be ½” wide as well, and vice versa.

You could make the cat jacket using hand sewing and not a sewing machine, if you have no way to obtain a sewing machine. However, it might not be a strong as one made with a sewing machine.

As a tip, you can lay your piece of fabric, plus your piece of lining material, plus your interfacing material, all on top of each other and pin the pattern through all three layers. Then when you cut out the shape, you can cut all three pieces in one step. If these three layers are too thick (i. e. the pin can’t easily go through them plus the pattern), you’ll have to do them separately.

As an alternative to interfacing, you could stuff the inside of the jacket with batting to give it a puffy, down-like look! You could even sew a criss-cross pattern on top of the vest, after it’s completed, to add to the effect.

Note that some nylon webbing can be quite thick. If you’ve decided to use really thick webbing, make sure you have the proper needle in your sewing machine.

Remember that when the two sets of flaps go around your cat, they’re going to overlap each other. So one piece of velcro needs to be on the inside of a flap and the other piece needs to be on the outside of a flap. If you’re an experienced seamstress, you could use some other type of closure other than velcro - buttons, a zipper, hooks, etc.

Not all cats are going to tolerate a jacket or harness right away. There are methods you can use to help train your cat to wear a harness, but beware of your cat’s limits. If these training methods don’t appear to be working, or your cat is really stressed and upset, you should stop and consult a veterinarian before continuing. Let your cat get to know the jacket. Put it down for them and let them sniff it. Give them treats while you do this. Associate positive things (like treats) with the harness so they aren’t scared. [10] X Trustworthy Source American Society for the Prevention of Cruelty to Animals Leading organization dedicated to the prevention of animal cruelty Go to source Lay the jacket over your cat, but don’t connect the velcro pieces. Feed them treats at the same time to keep them in a good mood. Do this a few times until they don’t appear overly nervous. After they’re use to the feel of something on their back, put the harness on and connect the velcro pieces. Again, do this while giving them treats and praising them. Some cats might simply walk around like nothing happened, others might try to fight the jacket or pretend like they can’t move. Leave the harness on for a little while, or until your cat is too upset. Repeat this several times, increasing the length of time your cat wears the harness. When you feel you cat is ready, attach the leash, carry him/her outside, and let them walk around. Always supervise your cat while they’re outside.

For the sake of our example, let’s assume our three measurements are 8”, 6” and 15”, where 8” and 15” are the two circle circumferences.

The plastic buckles should be the type that is called a “side release” buckle.

Do not fuse or melt two ends of a piece of paracord together.

For a step-by-step video on how to complete a cobra stitch, see here.

You can attach a leash clip directly to the paracord in the middle section, or you could attach a D ring to the middle section while you’re doing the cobra stitch.